Saw video thread

  • Thread Starter Thread Starter
  • #126
I’ve looked into that ... it may be more advantageous to find another that has and pay him $50 for a “run” and then get the computer printout
 
If the top cover looks like a rat chewed through it just to make a hole for a filter out the back. Imagine what the port work might look like. :O:|:

I'm not one to worry about port work looks long as they run good. But holy crap that is horrible work on that top cover.
Here I thought I was a hack. :lol:
 
  • Thread Starter Thread Starter
  • #132
Cut4fun said:
If the top cover looks like a rat chewed through it just to make a hole for a filter out the back. Imagine what the port work might look like. :O:|:

I'm not one to worry about port work looks long as they run good. But holy crap that is horrible work on that top cover.
Here I thought I was a hack. :lol:
Click to expand...

Yah , went a bit too far on the clearance ... R/D man ... got a new cover on order ... here’s a video before any port work was done ... tuned intake with K/N filter and tuned exhaust ... Saw has about 20 tanks of fuel thru at this stage ... approx 15-18% gains over brand new / stock WITH stock jug/slug NO Porting on this video , original jug/slug !https://youtu.be/tiysFN3-nL8
 
  • Thread Starter Thread Starter
  • #133
10A5F5EF-390B-4C8D-878D-B3362116E68F.jpg exhaust port from hot-woods ported 441cm ... no “imagining” required !
 
  • Thread Starter Thread Starter
  • #136
Little compare-0 video between a 462c (72.2cc) with tuned exhaust/intake stock jug/slug vs a Hotsaws101 461R (76.5cc) Extreme ported worksaw ... The 462c is bone stock except for the intake / exhaust mods , the 461R is ported and features a max-flo air system and a 460 unlimited coil ..... https://youtu.be/AjbZ2S95iBQ .......https://youtu.be/E0x4H66GZSE
 
That's a mean 461, sounds angry, the clear winner regardless of technique. The 462 almost caught it with the last cut, but still a ways off.
 
  • Thread Starter Thread Starter
  • #138
Nutball said:
That's a mean 461, sounds angry, the clear winner regardless of technique. The 462 almost caught it with the last cut, but still a ways off.
Click to expand...

Yah , 3 cuts with the 462c 32sec ; 3 with 461 28sec ... best cut with 462c a fuzz over 8 sec ; 461R fuzz under 8 sec ... same bar/chain fuel, wood and atmospheric conditions and operator (me) ... consider the 462c has a stock jug/slug and the 461 is Hotsaws101 ported ... with a hot-woods port the 462c should beat it with 20” bar/chain ... also it’s giving up some displacement at 72.2 cc vs 76.5 cc ..... I have a 441cm that’s hot-woods ported and I’ll try and run the 461R and see the results ... the 441cm is 70.7 cc so it’s down almost 6cc from the 461 at 76.5
 
Frankie said:
Yah , went a bit too far on the clearance ... R/D man ... got a new cover on order ... here’s a video before any port work was done ... tuned intake with K/N filter and tuned exhaust ... Saw has about 20 tanks of fuel thru at this stage ... approx 15-18% gains over brand new / stock WITH stock jug/slug NO Porting on this video , original jug/slug !https://youtu.be/tiysFN3-nL8
Click to expand...

This one was funny, did anybody watch it?

<iframe width="560" height="315" src="https://www.youtube.com/embed/tiysFN3-nL8" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe>
 
  • Thread Starter Thread Starter
  • #140
Yeppers ... live action no editing out mistakes ... I give it to ya straight-up ... but that’s what ya want right ? All or none ... no “glamour” shots here at Fabz acres lol !
 
  • Thread Starter Thread Starter
  • #146
461R Hotsaws101 vs 462c fastest cut ... ported 462c video comin real soon and it f’in el rip-0 s haha .... https://youtu.be/aa-02ALxJfk ... FF8441A0-F41A-4B82-A916-EF5E2625631B.jpg 462c torn-down ; notice the cast “stuffer” ala the 461... should make some good powa !!! ECB96B30-1B5D-4C6E-912B-3FECA23A5DCF.jpg mondo transfer feeding quad transfer ports ...
 
  • Thread Starter Thread Starter
  • #148
https://youtu.be/mFwKP1hU0DE ... 462c hot woods port ... approx 30% quicker than stock ... using stock off the roll STIHL RS chain 3/8 .050 ... with a square ground chain and rakers set accordingly a 20% quicker cut time can be obtained (for a gain of approx 50% over stock !!!).. More in this Saw but I’m satisfied with this version ... great combo of power and fuel economy !!!
 
You must log in or register to reply here.

Similar threads

Eric H-L
Chainsaw repair video series
Replies
3
Views
684
davidwyby
davidwyby
cory
The dreaded stripped threads, Husky 572
Replies
21
Views
897
huskihl
huskihl
cory
KOT
Replies
0
Views
338
cory
cory
Eric H-L
I can’t put a new chain on my saw!
Replies
8
Views
414
CurSedVoyce
CurSedVoyce
davidwyby
Yesteryear Saws
2
Replies
38
Views
2K
davidwyby
davidwyby
Back
Top