Search results for query: *

Easiest is a muffler mod, a bit hard to do on the Husky saws and make it look good without being/knowing a good welder. Basicly open the exhaust hole to 75-85% of the exhaust port opening, cut the limiters off the carb adjusting screws and re-tune the saw until it "fourstrokes" nicely. You...

Mine oils fine, with the seven pin on the 32", run the 8 pin, and, well, it runs fine but wants to burn up bars!!!!

Thats the other part of the conudrum Brian!! Yes, I have the Freakingstang built woods ported big bore 046. It's NIIIIIIIIIIIIIIIIIICE!!!!!! If I can't cut it with that saw and my 32" bar, I DON'T NEED TO!!! But yes, why do I need another saw that size?

This will be a felling saw as well. Most of the tree's I take on (for firewood) are 12"-20". My 046BB is wonderfull for this, but overkill, and thirsty!!! I'd like something lighter, but can't find anything, other than the 7900, worthy of putting the 046 down for. See my conudrum? I don't have a...

I don't need excuses, I need time!!! It's firewood time now, and people are screaming for OAK!!!!!

Well Fred, I really think for what I want, I need something in the 60cc class. I had just read so much about these saws, and I got a good buy on it, I would try it. At the same time I had an option to buy a 5100s for the same money, not sure that would have made me anymore happy? The 361 sounds...

Well, it wasn't really for sale, and others offered first? Oddly enough, the two people that told me it should do this or that, I offered to send it to them, pay shipping each way and for their time, refused the offer!! Sorry Justin, I will keep you in mind next time, ok?:D

Well, it seems to get more interesting!!! I couldn't get it where I wanted it, so I came up with an idea! I would ship the saw out to a few AS members, that I trust, and get their opinions on it! Good idea right? It got to the first house, they couldn't have had it more than four hours, and I...

Very thin with a shallow taper on he ends of them, almost rounded. And yes, 1/16 of a turn changes about 200 RPM.

Pulled and cleaned the carb. Had to adjust and adjust it to get it to run right. Then I ran two tanks through it at the woodlot. Runs better now, it will pull you into the cut now. A lot happier, I'll see how it wears in now. Andy

Interesting Magnus, I have been hearing it's lean a lot lately!!! May have to pull and clean the carb and play with it some more. I was just trying to set the RPM's in the realm of reality, and if I richen out the H jet it gets gutless really quick!!

Very well could be. Maybe I have higher expectations than what the saw is realisticly capable of.

That is why I widdend them so much Al, that is where the tourqe gains come from, as I have been told at least. I know they can be made into bad as saws, I just think this one was a lemon, and my point is I can make mods to a cheapie homeowner saw and have it keep up with the pro saw for a lot...

No I have not, so I have no baseline to compare it to. But the saw runs and cuts fine. It's just not at all what I thought it would be.

.325 with a 7 pin.I have been told to step up to 3/8's, but..............

Sorry Rich!!! What can I say, you always did know I was an odd duck:lol: I am waiting for Riverrat to chime in and give his review so you all don't think I am more than normaly crazy!;)

This saw has a shady history. I bought it used from a guy on AS that bought it online. He was sorryly disapointed with it.I got it and was even more so dissapointed. Come to find out, after modding it I had to cut the limit tabs off the carb so I could LEAN it out and get it o run right!! It was...

I have been told you can widden the ports .140" and raise and lower them .060" before you run into timming issues. I did do a litle research.

Been a while had to go llok again. When it was all said and done the transfers where ground out and blended to almost a sliver. The intake and exhaust ports where widdened .080"-.100". The intake port was lowered and the exhaust port was raised both by .040". I did my homework, and all of...

As Jeff brought up in another thread, he got to play with some of my toys this last weekend. My 046BB puts a smile on my face everytime I use it, and I think he was suprised at how it ran. The bi shocker was when I handed him my modded 346xp and 350xp. I will try not to taint this and let Jeff...