Search:

Type: Posts; User: Magnus; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    295
    Views
    38,181

    I can still order the White ones from Germany...

    I can still order the White ones from Germany suppliers.
  2. Replies
    295
    Views
    38,181

    As I understand it, GB had production in North...

    As I understand it, GB had production in North America and in AU. US chainsaw bar production is gone.
    The white ones I sold here was Austraila made. I think they still are. The orange was North...
  3. Replies
    295
    Views
    38,181

    Is there no GB bars any more? The AU made ones...

    Is there no GB bars any more?
    The AU made ones are available thru GB Germany I think.
  4. Replies
    42
    Views
    1,510

    I don't set saws by tach, its too misguiding. Too...

    I don't set saws by tach, its too misguiding. Too much that can go wrong. I set them after performance. When they run at its best its usually a great place to be.
    Ignitions today is a bit trixy and...
  5. Replies
    42
    Views
    1,510

    A clutch that is engaged and under load rarely...

    A clutch that is engaged and under load rarely wear excessively. If you have saw in low rpm were clutch engage, disengage all the time that will stress and wear out clutch prematurely.

    Most common...
  6. Replies
    59
    Views
    1,585

    I thumb throttle when bar is horizontal...

    I thumb throttle when bar is horizontal regardless of what it do.
  7. Replies
    59
    Views
    1,585

    Try it. A lot easier on wrist and you get a...

    Try it. A lot easier on wrist and you get a better and safer grip holding saw with horizontal cuts.
  8. Replies
    59
    Views
    1,585

    I cut hard wood as well before. They had branches...

    I cut hard wood as well before. They had branches all around trunk as any other tree so the maneuvering of saw was about the same, just less frequent. I had saw on trunk when possible in hard wood as...
  9. Replies
    59
    Views
    1,585

    How many here limb trees felled on ground carry...

    How many here limb trees felled on ground carry saw when limbing instead of letting it sit on trunk?
    Do any of you use the thumb/indexfinger loop to run handle thru?
  10. Replies
    59
    Views
    1,585

    Thats what I thought.

    Thats what I thought.
  11. Replies
    59
    Views
    1,585

    So always one handed and only vertical cuts?

    So always one handed and only vertical cuts?
  12. Replies
    59
    Views
    1,585

    I never climbed, but done some lift jobs years...

    I never climbed, but done some lift jobs years ago and can't remember I did different then.
    If saw change position its same thing if I stand on ground or a cut in a lift. I still change position...
  13. Replies
    59
    Views
    1,585

    Only time I really hold on to handle with left...

    Only time I really hold on to handle with left hand is when I change grip in right hand. A other times handle run thru hand in a loop made from thumb and index finger. those two fingers have contact...
  14. Replies
    59
    Views
    1,585

    I try explain in words. I shift position and...

    I try explain in words.
    I shift position and thumb throttle on under and upper side of trunk.
    Right hand wrist tilt the saw from side to side and up or down. Handle run loosely in left hand saw,...
  15. Replies
    59
    Views
    1,585

    If you have felling saw AND limbing saw I can see...

    If you have felling saw AND limbing saw I can see the use for it...
    Mostly I use same saw for felling and limbing so for me the more grip there is the worse handling I get.

    I don't like to hold...
  16. Its hard to test with accurate results. Measuring...

    Its hard to test with accurate results. Measuring and checking sparks will give you a hint, but thats about it.
    The electronic's inside can be broken. Then you get fine spark at wrong place in...
  17. Replies
    20
    Views
    1,323

    Haven't seen or heard any 385 or 390 blow...

    Haven't seen or heard any 385 or 390 blow bearings here. Seen some hard abused ones....

    Have a custemer here with one 575, two 576 that never past 3 moths. He has been running 7900 now going on...
  18. Replies
    20
    Views
    1,323

    385/390 is a wonderful saw! 394/395 I just...

    385/390 is a wonderful saw!
    394/395 I just tested a bit but it seemed to be a step up and closer to 3120 in its performance. I miss the "umpf" thats in 385/390 if that makes any sence to you..
  19. Replies
    20
    Views
    1,323

    I doubt that the 372 will be a vast improvement...

    I doubt that the 372 will be a vast improvement from 575/576. We'll see...
    Bottom end bearings, top end bearings, running hot, cracking, there is a number of issues with 575/576.
    Case on 572 look...
  20. Replies
    20
    Views
    1,323

    572xp is on the way as is the 462c-m.. Might...

    572xp is on the way as is the 462c-m..
    Might hang tight a bit and see when they come to a circus close to you.
  21. Replies
    102
    Views
    5,350

    The customers I have that get most out of their...

    The customers I have that get most out of their bars and chains is the ones that rotate chains, 5-10 on one bar and rim.
    By rotating you have even wear. If you run bar with replaceable sprocket it...
  22. Replies
    102
    Views
    5,350

    O like 1,6/.063 It libes well, as do 1,5/,058...

    O like 1,6/.063 It libes well, as do 1,5/,058 compared to 13/,050.
  23. Replies
    102
    Views
    5,350

    I sell bars and chains in 1,5 for several husqy...

    I sell bars and chains in 1,5 for several husqy users.
    One today with a 036 and 1,5 guage..
  24. Replies
    102
    Views
    5,350

    I can order Stihl chain in .325 and 3/8 in 1,3...

    I can order Stihl chain in .325 and 3/8 in 1,3 1,5 1,6 guage
    Same with Oregon.

    If you want same pitch and guage (even length in some cases) on saws from different brands, its fully possible.

    I...
  25. Replies
    102
    Views
    5,350

    Not sure I understand this correctly. All brands...

    Not sure I understand this correctly.
    All brands have all the different gauges to all saws. 1.3 1.5 1.6 no matter...
    You just need right chain to the bar.
    Mfg's like Oregon, cannon, Iggesund,...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4